Mémoires de Fin d’Etudes
Etablissement
Université de M’Sila - Mohamed Boudiaf
Affiliation
Institut de Physique
Auteur
MANARI, Abdelmalek
Directeur de thèse
Farsi Chaouki
Filière
Physique des Matériaux
Diplôme
Magister
Titre
RELATION ENTRE ECROUISSAGE, CONTRAINTES RESIDUELLES ET TENUE A LA CORROSION SOUS CONTRAINTES D’UN ACIER INOXYDABLE AUSTENO-FERRITIQUE.
Résumé
ملخص في هذه الدراسة، نحلل العلاقة بين التطرق والاجهادات الداخلية أو المفتعلة ومقاومة الصدأ تحت تأثير الاجهادات بالنسبة للفولاذ الغير قابل للصدأ المكون من عنصرين (أوستنيت + فيريت). ويتم تعيين الحالة الميكانيكية على سطح العينات عن طريق استعمال الأشعة السينية. تجارب الصدأ المحققة تحت تأثير قوة الشد المسلطة على العينات تدل على حد أدنى من التشقق ولكنه معتبر على مستوى الاجهادات الداخلية وبدرجة أقل بالنسبة للتطرق المحصل عليه بتسليط قوة شد مسبق ة. بالعكس من ذلك، فإنه في حالة تجارب الصدأ تحت تأثير الاجهادات الداخلية الناتجة عن Mpa الانحناء المسلط على عينات تكون مشوهة مسبقا بواسطة الشد، نجد حدا أكبر من الأول يمكن أن يصل إلى 150 . في هذه الحالة فإن نسبة التطرق تعتبر عنصرا هاما، وحسب الحد المحصل عليه يكون التأثير إما إيجابيا أو سلبيا. SUMMARY In this study, we analyze the relations between work hardening, the residual stresses or applied and susceptibility to stress corrosion of a two-phase stainless steel (austeno-ferritic). The mechanical state on the surface of the samples is carefully defined by diffraction of x-rays the tests of corrosion carried out under uniaxial load of traction applied, reveal a critical point of cracking very low but sensitive to the level of the initial residual stresses and little to the initial work hardening obtained by preliminary traction. On the other hand, in the case of the tests of stress corrosion residual obtained by elastoplastic inflection on samples deformed beforehand by traction, one finds a threshold definitely higher, always higher than 150 Mpa. In this case the rate of work hardening is an extremely significant factor; according to the level the effect reaches can be beneficial or harmful. RESUME Dans cette étude, nous analysons les relations entre l’écrouissage, les contraintes résiduelles ou appliquées et la susceptibilité à la corrosion sous contraintes d’un acier inoxydable biphasé (austéno-ferritique). L’état mécanique à la surface des échantillons est soigneusement défini par diffraction des rayons X. Les essais de corrosion effectués sous charge uniaxiale de traction appliquée, révèlent un seuil critique de fissuration très bas mais sensible au niveau des contraintes résiduelles initiales et peu à l’écrouissage initial obtenu par traction préalable. En revanche, dans le cas des essais de corrosion sous contraintes résiduelles obtenues par flexion élastoplastique sur des échantillons déformés préalablement par traction, on trouve un seuil nettement plus élevé, toujours supérieur à 150 Mpa. Dans ce cas le taux d’écrouissage est un facteur extrêmement important, selon le niveau atteint l’effet peut être bénéfique ou néfaste.
Date de soutenance
06-07-2004.
Pagination
92
Format
pdf
Statut
Traitée